HUVV铜芯聚氯乙烯绝缘聚氯乙烯扩套矿用电缆敷设在矿井中，一般场合对绞式聚乙烯绝缘聚氯乙烯护套市内通信电缆型号名称CPEV-S绞式聚乙烯绝缘聚氯乙烯护套市内通信电缆全聚氯乙烯局用电缆HJVVHJVVP105芯（21×3×0.5+21×2×0.5）的详细介绍全聚氯乙烯局用电缆制造标准：Q/TY一．。
铜芯聚乙稀绝缘聚氯乙稀护套铜丝编织屏蔽计算机电缆规格导体种类绝缘标称厚度mm编织单线直径mm外护套标称厚度mm电缆外径≤mm硬导体软导体1x2x0.759．41x2x8.710．11x2x1.51。
YQ,YQW轻型橡套软电缆用于轻型移动电器设备和工具YZ,YZW中型橡套软电缆用于各种移动电器设备和工具YC,YCW重型橡套软电缆用于各种移动电器设备，能承受较大的机械外力作用我橡塑电缆厂的野外用橡套电缆（YCW电缆，YZW电缆）是为适应野外用工矿企业调整发展的需要，生产性能优良的橡皮绝。
HYA5x2x0.4HYA5x2x0.5HYA10x2x0.4HYA10x2x0.5HYA20x2x0.4HYA20x2x0.5HYA30x2x0.4HYA30x2x0.5HYA50x2x0.4HYA50x2x0.5HYA100x2x0.4HYA100x2x0.5HYA200x2x0.4HYA200。
产品名称型号规格及范围：塑料绝缘和聚氯乙烯护套铁路信号电缆PTYAH,;PTYA;PZYA;PTYV;PTYY,;PTY22;PTY23;（PZY02;PZY03;PZY23PZY22）1/0.8mm（1/1.0mm）2-48芯适用于额定电压交流500V或直流1000V及以下的铁路信号联络、火警信号。
三极管的管型（PNP型三极管还是NPN型三极管）以及三极管引脚的判别是电子初学者的一项基本功。
有人了四句口诀：“三颠倒，找基极；PN结，定管型；顺箭头，偏转大；测不准，动嘴巴”。
我们来逐句进行解释分析。
三颠倒，找基极我们知道，三极管内部有两个PN结，三极管是PNP型还是NPN型的区别就是两个PN结的连接方式不同。
如下图所示是三极管及等效电路。
测量三极管是要使用万用表的欧姆档，档位的选择可以是Rx100档位，也可以是Rx1k档位。
RS-485通讯电缆RS-485通讯电缆在一般场合采用双绞线就可以，但在要求比较高的环境下可以采用带屏蔽层的双绞电缆。
在使用RS485通讯时，对于特定的传输线路，主机（召测设备）到仪表的485口间的电缆长度与数据信号传输的波特率成反比；这个长度主要受信号的失真以及噪声的影响所影响。
MHYAV（20*2*0.8mm、30*2*0.8mm）结构：铜丝线芯（线径为0.8mm）——线芯交联聚乙烯护套（由10种颜色构成的护套）——铁质粘结铠装层（铠装层的外部涂有绿色耐高温材料）——内护套‘交联聚乙烯护套’（颜色为黑色，经过200摄氏度高温挤塑而成）——外护套‘聚氯乙烯护套’（颜色为蓝色。
This is the General Purpose Cable in the UL standard. The applicable safety standard is UL1581. The commercial and general test conditions are similar and are approved for use in Canada and the United States. There is no smoke concentration specification for general-purpose grade cables, which are generally only used for horizontal running of the same floor, but not for vertical wiring of the floor.
6、铠装通信电缆电气特性：电缆符合基本电缆的全部电气要求。
7、电缆长度：机械保护型电缆是根据相应基本电缆的标准长度制造。
用途实心绝缘非填充型电缆用在交换区域做配线用，主要用于管道敷设，在架空安装时需要用吊线支承。
产品型号:HYAHYACHYATHYYHYVHYY23HYV23HYYT23HYA23HYAT23HYATC主要产品:充气电缆,自承式架空电缆,充油电缆,填充型电缆,屏蔽电缆,非屏蔽电缆HYA电缆_充气电缆的相关产品HYA电缆_充气电缆HYAHYACHYA23铠装通信电缆HYV22HYA53HY。
下面介绍电缆的选型和电缆截面的选择方法。
电缆型号的选择电缆型号的选择，与供电的可靠性、安全性及是否经济合理有很大的关系。
《煤矿安全规程》第四百六十七条对电缆的选用制定了如下选择要求：1.电缆实际敷设地点的水平差应与规定的电缆允许敷设水平差相适应。
一般是背板带宽和包转发率都满足的交换机才是合适的交换机。
背板相对大、吞吐量相对小的交换机，除了保留了升级扩展的能力外，就是软件效率/专用芯片电路设计有问题；背板相对小、吞吐量相对大的交换机，整体性能比较高。
摄像机码流影响清晰度，通常是视频传输的码流设定(包含了编码发送及接收设备的编解码能力等)，这是前端摄象机的性能，与网络无关。
通常用户认为清晰度不高，认为是网络原因造成的想法实际是个误区。
根据上面的案例，计算：码流：4Mbps接入：24*4=96Mbps1000Mbps4435.2Mbps汇聚：170*4=680Mbps1000Mbps4435.2Mbps接入交换机主要考虑到接入到汇聚之间的链路带宽，即交换机的上联链路容量需要大于容纳的摄象机数*码率。
控制电缆包括kvv电缆，kvvr电缆，zrkvv电缆，zrkvvp电缆，kvvp电缆，kvvrp电缆，kvvp2电缆，kvvp2－22电缆，nhkvv电缆，zrkvvrp电缆，kvv22电缆，zrkvv22电缆。
适用于各种火灾危险性较大，消防重要性较高的场所中的电器装置及控制系统。
2、敷设时环境温度≥0℃。
3、最小弯曲半径：4、无铠装层电缆，应不小于电缆外径的6倍。
5、有铠装或铜带屏遮结构电缆，应不小于电缆外径的12倍。
RVV聚氯乙烯绝缘、聚氯乙烯护套仪表用软电缆用于要求柔软的场合。
RVVP聚氯乙烯绝缘、聚氯乙烯护套仪表用屏蔽软电缆同RVV型，用于抗干扰场合。
HYA：铜芯实心聚烯烃绝缘挡潮层聚乙烯护套市内通信电缆。
Precautions for installation of power cables: keep 2m distance when the cable is installed in parallel with the thermal pipe, and 0.5m should be maintained when crossing. The cable shall be installed at a distance of 0.5m in parallel or across other pipelines. When the cable is directly buried and installed, the direct buried depth of 1-35kv cable is less than 0.7m. When 10KV and below cables are installed in parallel, the net distance between them shall not be less than 0.1m and 10-35kv shall not be less than 0.25m. The distance of cross installation is not less than 0.5m. Cable laying temperature lower than 0 ℃, bending radius: multi-core cable or 15 (D + D), a single cable 20 or more (D + D), (D for cable diameter, D) for the conductor diameter. ? 6KV and above cable connector:? When installing the terminal head of the cable, the semiconductor electrical shielding layer must be stripped off. During operation, the insulation shall not be damaged. The shield end should be flat and the graphite layer (carbon particles) should be clean. (2) plastic cable end copper tape screened and armor must be good grounding, the short circuit also follow this principle, avoid unbalanced three-phase run ShiGang armoured end produce inductive electromotive force, and even "lighter" and sheath and other accidents. It is required to use my tinplate to braid copper wire for grounding lead. When connecting with the cable copper belt, it should be welded with chromium-iron tin. ? The shield of three-phase copper tape should be connected with ground wire respectively. Note that the shielded ground wire and steel armor ground wire should be separately drawn out and insulated from each other. The position of the welded ground wire should be as low as possible. Basic re for cable terminals and intermediate joints: a. good conductor connection; B. The insulation is reliable, and it is recommended to use irradiated cross-linked heat-shrinkable silicone rubber insulation materials; C. good sealing; D. sufficient mechanical strength to meet various operating conditions. The end of the cable must be used to prevent water and other corrosive materials from corroding, in order to prevent the water tree caused by the aging of the insulation layer and breakdown. Crane or forklift should be used for the loading and unloading of cables. It is forbidden to run flat or lay flat. For installation of large cables, cable laying cart should be used to avoid external damage or abrasion caused by manual dragging. If the cable cannot be laid in time for some reason, it should be stored in a dry place to prevent sunlight from exploding and water entering the end of the cable. ? Note: the installation of wire and cable should be familiar with the performance of wire and cable installation personnel or full-time technical personnel, if there are still unclear matters, ball related technical department or technical department of our factory.